Mammut XT Wall Formwork

Mammut XT: Tie from One Side. Or Both!

Three tying methods in one system
The sytems integrated Combi tie of using any of the following tying methods and flexibly changing from one to another:

  • New: Tie from one side only using DW 20 tie-rods and plastic sleeves. The XT tie rod and articulated flange nut are joined firmly, forming one part.
  • New: Tie from one side only using taper ties without plastic sleeve.
  • Proven: Tie from both sides with DW 20 or DW 15 tie rods and plastic sleeves. The XT tie rod and articulated flange nut are joined firmly, forming one part.
 
Features & Benefits
Saving Time, Saving Money
Animation
Download
Complementary systems

FEATURES & BENEFITS

Panel

  • Symmetrical tie-hole and joint pattern on the concrete surface no matter what panel sizes you use
  • 25 cm width grid thanks to the large selection of panel heights (350, 300, 250 and 125 cm) and panels widths (250, 125, 100, 75, 50, 25 cm)
  • Corners of any wall thickness in 5 cm increments with only 3 outside and 2 inside corners. Their side lengths are 0/10/15 cm and 35/40 cm respectively

Pressure

  • Mammut XT is based on the proven and successful Mammut 350 system and its load capacity of 100 kN/m² according to the European standard DIN 1820 table 3, line 7

Panes Frame

  • Frame hot dip galvanised
  • The bump notch on large panels allows you to easily move the them into their final position

Multi-function profile

  • The large panels are equipped with a clamp holder alongside normal clamp positions. After stripping the formwork, attach each clamp to a holder and secure it with just one hammer blow. When moving panels from one pour to the next, the correct number of clamps travel with it, at hand and ready for the next assembly. No transport, no storage, simple logistics and time-saving are your benefits
  • Tie rod holder that plugs into the multi-function profile via pin. Thus, the parts needed for tying travel with the panel to the next pour. They do not have to be transported, stored and looked for
  • All cross stiffeners are multi-function profiles with welded-in DW nuts. Attaching accessories is easier than ever

Tie holes, panel connections

  • No difference between two sides of the formwork setup. Reduce tie parts by 50%. Three tying methods in one system. No additions, modifications or conversion parts
  • The Combi tie is built into the frame, i.e. no protruding or loose parts
  • Combi tie with rotating sphere for two settings: one with conical anchor sleeve and one with DW-20 thread
  • Save the articulated flange nut on one side entirely, the number of parts is reduced by 50%

All-plastic facing alkus

All-plastic facing alkus, no swelling or shrinking

  • No change in dimensions due to moisture; no rotting or fungal decay; durable
  • Built in flush with panel frame; improved and consistently even concrete surfaces from the first pour to the last

Easy repair of scratches or drill holes etc. on site with the same polypropylene material

  • No down times for repairs
  • Permanent availability of panels

Screwable and nailable without chipping off of top layer

  • Easy handling

The alkus facing lasts as long as the Frame  

  • No re-facing necessary and thus no disruptions of work flow
Technik & Vorteile der Mammut XT Wandschalung
 

Tie from one side

Tie from one side

The Combi tie is built into the frame, i.e. no protruding or loose parts. No conversions, modifications or add-ons required when switching from one to twosided tieing.

Reduced parts

Reduced parts

You save the articulated flange nut on one side entirely, the number of parts is reduced by 50%.

Park position at the panel

Park position at the panel

Selbstsichernder Parkpositions-Halter für Zubehör und angeschweißter Klemmhalter für Schalschlösser. Das Zubehör bleibt beim Umsetzen am Element. Kein extra Lagern, Suchen oder Transportieren des Zubehörs nötig.

Attachments

Attachments

All cross stiffeners are multi-function profiles with welded-in DW nuts. Attaching accessories is easier than ever.

Panel connection

Panel connection

Panels are aligned and joined firmly with the MEVA clamp, closed by just a few hammer blows. The clamp fits anywhere on the frame, thus enabling safe tieing even in offset position. It has no losable parts

Alignment

Alignment

The bump notch on large panels allows you to easily move the them into their final position

 

Download

Complementary systems

  • BKB: Platform for Safe Pours

    MEVA foldable working platforms, walkway brackets and comprehensive safety accessories make your concrete pours safer and faster. The foldable working platform is simply swung into position on the AluStar, StarTec, Mammut or Mammut 350 wall formwork panels.

  • Circo: Strong circular column formwork for circular columns

    Circo is a robust steel system with integrated hinge joints for circular columns. It is available in 5 cm steps from 25 to 80 cm and in heights of 50, 100 and 300 cm. The two shells are closed using the standard M clamp.

  • Heavy-duty braces Triplex

    Modular system for heavy duty bracing. The brace lengths are variable and can be used to support and align high walls and columns beyond 6 m heights.

  • KAB: Foldable Safety Climbing Platform

    MEVA foldable working and climbing platform. It is delivered to the site folded and pre-assembled and can be used as a climbing platform.

  • Mammut 350: The100-kN/m² heavy-duty wall formwork

    Heavy-duty wall formwork. Large panel size 3.50 high, 2.50 width footprint. 100 kN/m² concrete load capacity throughout the system.

  • MEVA FormSet MFS: stop ends, safety anchors

    MEVA FormSet anchors for single-sided formwork, stop end rail and stop end bracket for slab edges and cantilevering slabs with safety mesh for slab edge fall protection

  • Push-pull props R and bracing brackets SRL for wall formwork

    Push-pull props R and bracing brackets SRL are used to align and support wall formwork. Push-pull props SRL have left- and right threaded spindles. The brace bracket 250 consist of a push-pull-prop R 250 (190 - 320 cm) and bracing bracket SRL 120 (90 - 150 cm).

  • Radius: The Circular Formwork System

    Radius is the state-of-the-art circular wall formwork systems for all round walls from a radius of 250 cm upwards. It is compatible with the Mammut 350 wall formwork system and is joined using the same M formwork clamp. It has a sturdy 6 mm steel facing for a superior concrete finish. Its benefits are very quick, easy assembly and the easy selection of any radius. Box outs are aligned using high-performance magnets. Predestined for architectural requirements.

  • SecuritBasic: Safety System for MEVA Wall Formwork

    Comprehensive, modular safety system for MEVA wall wall formwork systems. Easy, standard attachment to the multi-function profile. Baukastensystem mit Betonierbühne, Rückenschutz, Frontgeländer und Durchstiegsluke mit Leiter und Stirngeländer. Befestigung an der Funktionsstrebe des Wandschalungssystems. Richtkonsolen am Rücken der Laufkonsole, dadurch keine Unterbrechung der Arbeitsbühne.

  • Support Frame STB and Support Brackets SK: Strong and Slim

    Heavy-duty support frame for single-sided walls beyond 12 m high. The basic unit fits on any truck. Support frame STB 300, can also be used horizontally.

Request a Quotation

 
 

Invest in MEVA Used Formwork

MEVA Original Used Formwork

Rental Formwork

MEVA Rental Formwork
 
All Plastic Facing alkus
MEVA Frame Profile
... more than just formwork
  •  Select language

    Select continent and country. Language selection optional.

  •  Contact
  •  Search

    Search on our website.

  •  Newsletter

    Subscribe to our monthly newsletter.